AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
![]() Hold the SYNC button down and then push the rotary to reset Pitch to its default (zero) value. Hold the SYNC button down and then use this rotary to adjust the Pitch (Tempo) of the track. When a Loop is active, hold SHIFT down and then use the rotary to move the loop backwards/forward by 1 beat. Push the rotary to activate/deactivate an automatic Loop. LOOP SIZE: : Turn this rotary to adjust the size used by automatic loops, or to change the length of the current loop.Hold SHIFT down and then slide to scratch the deck. While track is playing : - Slide your finger on the touch-strip to pitch-bend (temporary slow-down/speed-up the deck). While track is paused : - Slide your finger on the touch-strip in order to fine-tune the position of the Audio Pointer - Hold SHIFT down and then slide the touch-strip to fast seek through the track. Once a side of the touch-strip is touched, you can then use the entire touch-strip to apply to the same deck. In Dual mode : the left side of the touch-strip applies to the left deck, while the right side applies to the right deck. Deck selection is done via SHIFT+FX1/FX2 ASSIGN buttons or from the A/B select buttons on the VirtualDJ GUI. In Single mode : the entire touch-strip applies to the selected deck. The small dots above the touch-strip will indicate the selected mode (left half blue - right half orange for Dual mode or blue/orange for Single mode depending on the selected deck. Press the left FX1/FX2 ASSIGN buttons to set the touch-strip to the Single mode and at the same time select the left deck, or the right FX1/FX2 ASSIGN buttons to set the touch-strip to the Single mode and at the same time select the right deck - While in Single mode (left or right FX1/FX2 ASSIGN buttons are lit), press one of the unlit buttons to select the other deck, or press one of the currently lit buttons to return to the Dual mode. How to toggle between the 2 modes While SHIFT is held down : - If the FX1/FX2 ASSIGN buttons are unlit, the Dual (default) mode is selected. Use SHIFT+ FX1/FX2 ASSIGN buttons to select one or the other. TOUCHSTRIP: The Touchstrip can operate in Single or Dual (default) mode.You can switch between the 2 different modes of operation by holding down SHIFT and pressing the LOAD (10) button on each deck. Hold SHIFT and press a button if you want to stop playing the selected sample. If a bank has more than 4 samples, the left side will control samples 1 to 4 and the right side samples 5 to 8. If a bank has less than 5 samples, both sides will control the same samples. On Sampler mode each one of buttons pads triggers a sample from the selected Sampler Bank of VirtualDJ. Hold SHIFT and then press a button to delete its assigned Hot Cue Point. Once it is assigned, the Hot Cue Button will light on. When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired point in your track. HOTCUE/SAMPLER: These buttons offer two different operation modes: On HotCue mode each one of the 4 buttons assigns a Hot Cue Point or jumps the track to that Hot Cue Point (if assigned).*Note: if the SYNC button is released without the LOOP SIZE rotary being touched, the Sync action will be performed. Hold down SHIFT and press this button to set this deck as Master Deck (for 4 decks skins) Hold* down SYNC button and then use the LOOP SIZE rotary to adjust the BPM of the track. SYNC: Press this button to automatically match the corresponding Deck's tempo with the opposite Deck's (or the Master Deck’s if using a 4 decks Skin) tempo and phase. ![]() Hold down SHIFT and tab this button a few times to set a new BPM for the track (in case automatic BPM detection got it wrong) Several software functions (such as HotCues and Loops) will apply temporarily on the track, and the track will return to the position it would have been if those functions were not triggered. To continue playback without returning to the Temporary Cue Point, press and hold the Cue Button, then press and hold the Play Button, and then release both buttons. Releasing the Cue Button will return the track to the temporary Cue Point and pause it. If the Deck is paused, you can press and hold the Cue Button to play the track from the Temporary Cue Point. (If you did not set a Cue Point, then it will return to the beginning of the track.). During playback, you can press the Cue Button to return the track to this Cue Point. CUE: When the Deck is paused, you can set a temporary Cue Point by using the TOUCHSTRIP (6) to place the Audio Pointer at the desired location and then pressing the Cue Button.S SHIFT : Hold this button down to access secondary functions of Kontrol X1 MKII Native Instruments - Kontrol X1 MKII KONTROL X1 MKII BASIC CONTROLS ![]()
0 Comments
Read More
Leave a Reply. |